How do I reset my HP ProCurve 2626?

How do I reset my HP ProCurve 2626?

Factory Reset When enabled, the switch can be reset to factory defaults by depressing the “Clear” and “Reset” buttons together, releasing the “Reset” button while holding the “Clear” button down, and releasing the “Clear” button as soon as the “Test” light begins to flash rapidly.

How do you reset a ProCurve switch?

To initialize, or reboot, a ProCurve Switch, perform the following steps:

1. Press the small, recessed Reset button on the face of the switch.
2. Issue the command, reload from within the CLI.
3. Or, issue the command, boot system flash to reboot into either primary or secondary flash.

How do I restore HP switch settings?

HP Procurve – Backup and Restore a Configuration

1. Backup a configuration.
2. Launch Putty, select the COM port of your serial to USB adapter and click “Serial”
3. Select “Session” from the left hand pane and adjust the settings as shown below.
4. Click open.
5. Log into the device using the log in credentials.

How do I reset my HP ProCurve switch?

Continue to press the Clear button while releasing the Reset button. When the Self Test LED begins to blink, release the Clear button. The switch will then complete its self test and begin operating with its configuration restored to the factory default settings.

How do I factory reset my HP 2920?

Using Clear/Reset

1. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
2. Continue to press the Clear button while releasing the Reset button.
3. When the Self Test LED begins to flash, release the Clear button.

How do I turn off HP Procurve switch?

The most graceful way to shutdown an E-series Procurve switch is to do a “write memory” command at the CLI, (alternately exiting the menu interface or committing a change on the WebUI), wait for the command to complete, then pull the plug. If you want to reboot, you can do a “reload” or a “boot” command.

How do you restart a switch?

Holding down the Switch’s power button for 12 seconds will force a shutdown and reset the Switch. You won’t lose any saved data. After the console powers off, wait a few seconds, then tap the power button again, and it should reboot and work normally.

How do I reset my HP ProCurve Switch to factory default?

To execute the factory default reset on the switch, perform these steps:

1. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
2. Continue to press the Clear button while releasing the Reset button.
3. When the Self Test LED begins to blink, release the Clear button.

How do I reset my HP ProCurve 2510 to factory settings?

How to reset a ProCurve 2510-24g to default settings

1. Press in both the Clear and Reset buttons (tiny buttons on the left edge)
2. Release the Reset button after the port lights come on (~2 seconds)
3. When the Self-Test LED starts flashing (to the left of the Clear and Reset buttons), release the Clear button.

How do I save my HP Procurve running-config?

There are three ways to save a new configuration:

1. In the CLI: Use the write memory command. This overwrites the current startup-config file with the contents of the current running-config file.
2. In the menu interface: Use the Save command.
3. In the WebAgent: Click Save.

How do I restore a config to a Cisco switch using putty?

Ensuring that any Windows firewall is OFF.

1. Launch Putty and point it at 10.0.0.3 using Telnet.
2. The prompt should show “switch#”
3. Wait a good few minutes.
4. After about 10 minutes power cycle the switch.
5. When it comes back up it should be as the production switch.

Where can I find HP ProCurve switch 2600 installation and getting started?

HP ProCurve Switch 2600 Series hp procurve switch 2600 series installation and getting started guide Power over Ethernet Devices HP ProCurve Switch 2600 Series Installation and Getting Started Guide © Copyright 2003 Hewlett-Packard Development Company, L.P.

What kind of switch is the j4900c?

J4900C J4900C – ProCurve 2626 Switch Summary The ProCurve Switch 2600 series is a collection of low-cost, stackable, multi-layer, managed switches with 48, 24, or 8 auto-sensing 10/100 ports and dual-personality ports for 10/100/1000 or mini-GBIC connectivity. Related products Technical Features

How many ports does a 2626 switch have?

J4900C – ProCurve 2626 Switch. The ProCurve Switch 2600 series is a collection of low-cost, stackable, multi-layer, managed switches with 48, 24, or 8 auto-sensing 10/100 ports and dual-personality ports for 10/100/1000 or mini-GBIC connectivity.